Constellium ALPLAN® 6061 Rolled Precision Aluminum Plate, Milled Both Sides

Precision plates in ALPLAN® 6061 are milled on both sides and have a very low level of residual stress, thus avoiding excessive deformation during machining. Thanks to its very good dimensional stability and the elimination of surface milling operations, ALPLAN® 6061 plates enable to realize significant cost and time savings in machining, when compared to normal rolled plates.

Information provided by manufacturer

物理性能	额定值 (公制)	额定值 (英制)	测试方法
密度	g/cc	lb/in³

机械性能	额定值 (公制)	额定值 (英制)	测试方法
Hardness, Brinell	@Thickness 7.90 - 25.0 mm	@Thickness 0.311 - 0.984 in
	@Thickness 60.0 - 150 mm	@Thickness 2.36 - 5.91 in
	@Thickness 25.0 - 60.0 mm	@Thickness 0.984 - 2.36 in
抗张强度	>= MPa @Thickness 100 - 140 mm	>= psi @Thickness 3.94 - 5.51 in	Temper T651; Standard EN 485-2
	>= MPa @Thickness 7.90 - 12.5 mm	>= psi @Thickness 0.311 - 0.492 in	Temper T651; Standard EN 485-2
	>= MPa @Thickness 12.5 - 40.0 mm	>= psi @Thickness 0.492 - 1.57 in	Temper T651; Standard EN 485-2
	>= MPa @Thickness 40.0 - 80.0 mm	>= psi @Thickness 1.57 - 3.15 in	Temper T651; Standard EN 485-2
	>= MPa @Thickness 80.0 - 100 mm	>= psi @Thickness 3.15 - 3.94 in	Temper T651; Standard EN 485-2
	MPa @Thickness 60.0 - 150 mm	psi @Thickness 2.36 - 5.91 in	Typical Strength
	MPa @Thickness 7.90 - 25.0 mm	psi @Thickness 0.311 - 0.984 in	Typical Strength
	MPa @Thickness 25.0 - 60.0 mm	psi @Thickness 0.984 - 2.36 in	Typical Strength
抗张强度(屈服)	>= MPa @Strain 0.200 %, Thickness 7.90 - 12.5 mm	>= psi @Strain 0.200 %, Thickness 0.311 - 0.492 in	Temper T651; Standard EN 485-2
	>= MPa @Strain 0.200 %, Thickness 12.5 - 40.0 mm	>= psi @Strain 0.200 %, Thickness 0.492 - 1.57 in	Temper T651; Standard EN 485-2
	>= MPa @Strain 0.200 %, Thickness 40.0 - 80.0 mm	>= psi @Strain 0.200 %, Thickness 1.57 - 3.15 in	Temper T651; Standard EN 485-2
	>= MPa @Strain 0.200 %, Thickness 80.0 - 100 mm	>= psi @Strain 0.200 %, Thickness 3.15 - 3.94 in	Temper T651; Standard EN 485-2
	>= MPa @Strain 0.200 %, Thickness 100 - 140 mm	>= psi @Strain 0.200 %, Thickness 3.94 - 5.51 in	Temper T651; Standard EN 485-2
	MPa @Strain 0.200 %, Thickness 60.0 - 150 mm	psi @Strain 0.200 %, Thickness 2.36 - 5.91 in	Typical Strength
	MPa @Strain 0.200 %, Thickness 7.90 - 25.0 mm	psi @Strain 0.200 %, Thickness 0.311 - 0.984 in	Typical Strength
	MPa @Strain 0.200 %, Thickness 25.0 - 60.0 mm	psi @Strain 0.200 %, Thickness 0.984 - 2.36 in	Typical Strength
伸长率 (断裂)	@Thickness 80.0 - 100 mm	@Thickness 3.15 - 3.94 in	Temper T651; Standard EN 485-2
	@Thickness 100 - 140 mm	@Thickness 3.94 - 5.51 in	Temper T651; Standard EN 485-2
	@Thickness 40.0 - 80.0 mm	@Thickness 1.57 - 3.15 in	Temper T651; Standard EN 485-2
	@Thickness 12.5 - 40.0 mm	@Thickness 0.492 - 1.57 in	Temper T651; Standard EN 485-2
	@Thickness 7.90 - 12.5 mm	@Thickness 0.311 - 0.492 in	Temper T651; Standard EN 485-2
	@Thickness 60.0 - 150 mm	@Thickness 2.36 - 5.91 in	Typical Elongation
	@Thickness 7.90 - 25.0 mm	@Thickness 0.311 - 0.984 in	Typical Elongation
	@Thickness 25.0 - 60.0 mm	@Thickness 0.984 - 2.36 in	Typical Elongation
弹性模量	GPa	ksi

电气性能	额定值 (公制)	额定值 (英制)	测试方法
电阻率	ohm-cm	ohm-cm	Temper T651

热性能	额定值 (公制)	额定值 (英制)	测试方法
线性热膨胀系数	µm/m-°C @Temperature 20.0 - 100 °C	µin/in-°F @Temperature 68.0 - 212 °F
导热系数	W/m-K	BTU-in/hr-ft²-°F	Temper T651

构成要素属性	额定值 (公制)	额定值 (英制)	测试方法
铝			as balance
铬
铜
铁
Magnesium, Mg
锰
硅酮
锌